Gabe's Ghetto-Verb (how to hook up a spring tank)

Moderator: interruptor

Post Reply
Mike Manewitz
Posts: 1
Joined: Tue Apr 30, 2002 8:16 am

Gabe's Ghetto-Verb (how to hook up a spring tank)

Post by Mike Manewitz » Tue Apr 30, 2002 8:16 am

I was reading an issue of Big Daddy about recording funk and there was a technique listed there you that I've yet to try out. I'm going to type this out because not everyone can get a backissue of the mag and their content is yet to be online. <BR> <BR>Big Daddy #5 <BR>pg 80 <BR>Shitty Is Still Pretty: Anatomy of a Heavy Funk 45 <BR>by: Gabriel Roth &#40;producer for Desco/Daptone&#41; <BR> <BR>&#40;Exerpt&#41; <BR>Figure 1: Gabe's Ghetto-Verb <BR>Take the spring tank out of the back of a guitar amp or organ or anything else that you find that has a spring reverb. &#40;You can order a Fender reverb tank through any music store for about $20&#41; Use the biggest one you can find. You can use two channels of your mixing console for a pre-amp and a post-amp &#40;Channels 11 and 12 for this example&#41;. Patch your auxilary output &#40;effects send&#41; into the input of Channel 11. Patch the output &#40;direct out&#41; of Channel 11 into the input of the spring tank. Patch the output of the spring tank in to the input of Channel 12. Patch the output &#40;direct out&#41; of Channel 12 into either the input of another channel &#40;e.g. Channel 24&#41; or into an effects return to use as a reverb return. DO NOT BUSS EITHER CHANNEL 11 OR 12 TO THE MAIN MIX. You are using these channels only to pre-amp and post-amp the springs and do not want to hear them in the mix. Boos tthe highs and cut all the lows on the pre-amp channel &#40;Channel 11&#41;, and do the opposite &#40;cut the highs and boost the lows&#41; on the post-amp channel &#40;Channel 12&#41;. Though the EQ settings should cancel each other out when the signal passes through both channels, cutting the low end on Channel 11 will decrease the high-energy bass frequencies passing into the springs which would normally cause excessive distortion, and cutting the treble on Channel 12 will minimize the electronic hiss generated by all these successive pre-amps. <BR>&#40;end Exerpt&#41; <BR> <BR>Hope that's of help to someone.

User avatar
interruptor
Posts: 1200
Joined: Sun Sep 04, 2005 11:46 pm
Location: Switzerland
Contact:

Gabe's Ghetto-Verb (how to hook up a spring tank)

Post by interruptor » Tue Apr 30, 2002 9:13 am

yo thanks mike! <BR> <BR>this is a nice addition to Dubcreator's post discussed <A HREF="http://www.interruptor.ch/cgi-bin/discu ... 1">here</A>. the new idea in this case is to use one mixer channel each as pre and post amp.

DELETED

Gabe's Ghetto-Verb (how to hook up a spring tank)

Post by DELETED » Sat Jul 08, 2006 1:16 am

DELETED

DELETED

Gabe's Ghetto-Verb (how to hook up a spring tank)

Post by DELETED » Sat Jul 08, 2006 9:04 am

DELETED

DELETED

Gabe's Ghetto-Verb (how to hook up a spring tank)

Post by DELETED » Tue Jul 18, 2006 12:10 am

DELETED

Post Reply